How to make your own DIY leather bicycle grips (with wasted materials)

(This hack was featured in the front page of instructables.com)

I have been using these leather grips for a week now and I can honestly say that they are amazing. And they look awesome as well. It’s weird having strangers tell you that I shouldn’t invest on my beat up bicycle, by buying expensive parts! They wouldn’t believe that these grips are homemade with straight out of the bin materials! I ‘ve never had proper bicycle grips in my life. All I had was worn out bicycle grips or new very cheap ones. My DIY leather grips are my first proper very expensive looking grips. And I got them for free. Check bellow how I did it.

I’ve only used:

– A pair of worn out lock-on grips (if you don’t have, or you can’t find in your friends’ garage, you can buy them off ebay for around 3$)

– an (unusable) leather belt that you don’t want/like (non-slip, tough, amazing feel, beautiful looks, your hands doesn’t smell rubber after the ride, doesn’t leave black spots on your hands.)

– razor / knife

– A good pair of scissors

– a piece of thick fish line (incredibly resilient to the elements, most of the times you can find it for free, looks great, amazingly strong)

– A Dremel

– Needle-nose pliers

Firstly, strip off the worn out rubber using the razor. Remove most of the rubber without worrying too much about it. We need some leftovers so the leather parts don’t slide around.

IMGP4275

IMGP4276

Then, find out how many pieces of leather fit in your grip. If they can’t fit perfectly, make a thinner strip for each grip so they can cover the whole length. By wrapping the belt around the grip you can see where to cut it and then with your scissors trim it enough so the two ends almost touch each other (there should be a gap).  When you have them ready, open some holes with the Dremel. Try to make the holes on each end of the leather strip isometric. The holes must be as tight as possible (maybe as small as the fishing line).

IMGP4277

IMGP4278

Now, cut diagonally the end of the fishing line so it goes through the holes more easily. Using the needle nose pliers grab the end and make it go through the top hole and then the hole bellow (from the other side). Now, make it go through the same holes again but this time take the end and make it go through the next top hole. Don’t make it tight yet.

IMGP4281

Using your pliers squeeze the space between the threading so the two ends snug to each other perfectly.

IMGP4286

When you finish the first piece of leather, make all the threading tight. For the next strip make the line go through the next hole and keep doing what you did with the first.

IMGP4283

When you finish the threading, make it tight enough and then make two knots on each end. Hold the knot down as you pull the fishing line so it stays as close to the hole as possible. Using a lighter, make the end of the pliers very hot so you can melt and flatten the knot to prevent it from unbinding.

You can use a fork to make the threading very tight!

IMGP4287

They look nice, aren’t they?
IMGP4290IMGP4289

Advertisements

7 Comments Add yours

  1. Alan Holbrook says:

    Great job. I think I’ll try this.

  2. Pandoheas says:

    Thanks Alan! They are the best grips I have had, give them a try and you will be amazed

  3. John F. Bramfeld says:

    Very nice looking. You will want to protect them. For my baseball gloves I use A & D ointment, which is a mixture of lanolin and petroleum jelly. Rub it on generously and don’t worry that it doesn’t seem to soak in. Take a hair dryer to it and watch it instantly melt and soak in.

    1. Pandoheas says:

      Thanks a lot John. Actually I was worried a bit about rain (although so far they seem to hold up greatly), so your advice is much needed. I am a little bit confused with the A&D ointment, are you using the one that is for diaper rush?

      1. John F. Bramfeld says:

        Absolutely. Read the ingredients: petrolatum and lanolin. It it’s good enough for your baby’s butt, it’s good enough for your Wilson outfielder’s glove; and if it’s good enough for an outfielder’s glove, it’s good enough for bicycle grips. Plus, it lasts a lot longer on leather than it does under a diaper.

      2. Pandoheas says:

        That’s very interesting, thanks for sharing! I’ll try find a European alternative!

Comment freely

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s